Category: Hard

Amp #4 – Something JCM800-like

I’m going to be short and to the point since I’m poor at writing. It was finally time to build amplifier #4! This time I wanted to have another go at something high-gain (because I think that’s pretty cool).

I started out with the JCM800 #2204 schematic and used that as the general structure for the gain channel. I wanted a 30W-ish EL34 push-pull output stage, so I reused (with appropriate modifications) the output stage I put together for amp #3. I also had the output and power transformers ready as I scrapped amp #2 (it didn’t work properly, go figure…); a Hammond 1750Q and 372FX, which gave me some design directions.

After prototyping and going through several iterations I ended up with a two channel amp, high-gain and clean, with a blending phase inverter because I thought that would be fun. But since blending both channels in the P.I. would prevent the use of negative feedback, I also added, again for fun, a passive switching scheme that could take the amp between blending both channels, and muting one channel while giving the active channel the option of having negative feedback applied.

I had great fun and success building the previous amp on fiberboard, so I wanted to do the same this time, foregoing the point-to-point disaster that was amp #2 ๐Ÿ˜‰

I always forget how much work goes into building an amp from scratch. I must have been working on this six months straight, not counting the idea and drawing phase. And the shear price of all the parts had to be divided across many months anyway. This is certainly not a cheap hobby…

Lots of more or less interesting images of the amp taking form.

Spent some time designing nice face- and back plates, and got them etched in acrylic plastic from . Came out really great at a reasonable price. And of course I ended up bothering the circuit and ditching the “Mid” control in favour of an “Output” not long after. Typical! ๐Ÿ™

No big, complicated build without figuring out what’s wrong and doing some changes along the way. Notice the fire extinguisher.

Had to build a house for it as well. Not the most exiting part of the project, but it’s nice seeing everything coming together.

And finally, done.

I’m pretty happy how it ended up. Here’s a quick, off-the-top-of-my-head feature list:

  • High-gain channel in the spirit of the JCM800.
    • James tonestack with shift control (based on idea from Merlin Blencowe’s books).
    • Less bright than the JCM800, because I don’t like too bright.
    • Gain into- and out of the gain channel for some added possibilities (turned out essential for being able to blend the two channels).
    • Parallel FX-loop
  • Clean channel in the spirit of the DC30.
    • “Big muff”-style tilt control for single adjust of both bass and treble.
    • Not enough amplitude compared to the gain channel. Next time…
  • Master volume and presence control in the output stage.
  • 30-ish watts of cathode biased EL34 push-pull output. I like cathode bias for the additional fail-safe. And it sounds good ๐Ÿ™‚ Oh, and no manual bias adjustments required.
  • Blending of gain and clean channels possible (no NFB).
  • Single channel output (with or without NFB).

The schematic isn’t 100% when it comes to drawings of transformers, impedance switch etc. I didn’t want to spend time drawing more components in EagleCAD, so I just went with something close.

 

Updated: 29 November, 2017 — 00:06

Tap-Tempo Clock

Update (25.04.2016): The new version (v2) is up and running, and I’ll try to share as much as possible on github.

Source code

Pinout

Example schematic (not yet verified)

Update (09.07.2014): And here’s the new vero layout! Unfortunately I haven’t verified this one as I patched my original, faulty board rather than creating a new one. But I have looked it over and it should be good ๐Ÿ˜‰

For those few of you interested in building this for yourself, I’ll try to stock the shop section with a few pre-programmed Tap-Tempo Clock chips as soon as the empty ones I ordered arrives. If possible I’ll also include a 20-pin DIP socket and the 8MHz crystal.

TapTempoClock

Tap-Tempo Clock box keeping my tremolo sync’ed.

TapTempoClock in action (more…)

Updated: 25 April, 2016 — 23:05

Amp #3

Update (18.05.2014): I’ve made a few changes, mainly removing the FX-loop, and also put together a basic layout since I’ve had several requests for that as well. But to keep in mind this isn’t a simple color by numbers project; you need to know how to wire all of this properly, and you also have to keep safety in mind working with high voltages!

proto_one_15w_schematic_2_0ProtoOne_2_0_layout

(more…)

Updated: 18 May, 2014 — 13:56
SabroTone © 2010-2016 Frontier Theme